How to Repair a Toilet

A toilet is the most used part of a house. So it needs regular maintenance. If you hire a professional plumber for fixing a Leaking Toilet, it will be very costly for you. The best toilet repair kit can quickly solve your problem. A toilet repair kit has all the parts that a toilet needs. To repair the leaking toilet, you first need to identify which sections are required to repair.

How to fix a leaking toilet tank

A leaking toilet can be repaired by changing out the rubber gaskets around the tank bolts and the spud washer, which can deteriorate and fail due to hard water and minerals.

Required elements:

● screwdriver,

● small wire brush

● adjustable wrench,

● sponge,

● White vinegar, and rags.

Now start the project

1 At first, turn off the water at the shutoff valve below the tank.

2 Now drain the tank entirely as well flush the toilet and use a sponge to soak up any remaining water in the tub.

3 You must use the adjustable wrench to hold the nut located on the underside of the tank bolt.

4 use screwdriver to unscrew the tank bolts

5 Then remove the tank from the bowl and lay it down.

6 Remove the old spud washer and insert the new spud washer over the spud nut.

7 Now remove the bolts and gaskets and then clean around the holes on the tank. Now Place the new gasket onto each pin. Then reinstall the nuts onto the nails and gently tighten them by hand until they're snug. Finally, replace the tank on the bowl.

How to repair a Leaking Toilet

To repair a leaking toilet required tools:

● A new wax ring

● Two sets of 5/16-in. diameter water closet bolts

● A tube of silicone-based caulk, in a color to match the toilet

● A package of plastic toilet shims if your bathroom was rocking

Now start the project:

1 Loosen the bolts

At first, unscrew the water closet nut with a wrench. Then Loosen the nut just enough to squeeze in a hacksaw blade below the nut and saw through the bolt.

2 Now shut off the water supply valve and remove the water line leading to the tank. After turning off the tap and flushing the toilet, look for the tub and listen to trickling water. If you see the water is still running, you'll have to shut off the main water valve in the house and replace the lid with a new one.

3 Clean up around drain whole and Prep for the original parts

4 Flange Reinforcement Rings

5 Remove the old flange screws and slip each half of the flange support beneath the flange edges.

How to fix a running toilet

Fixing a running toilet is not an easier task. A running toilet can drive you nuts. It is a flapper that doesn't seal. Here some necessary steps to fix a running toilet:

Test the Flapper

When you hear the water is running and listen for it to stop, push down on the flapper with a stick. If it stops, then you check the flapper. If it isn't sealing properly, then replace it. At last, check the fill tube length and cut it back, so it's at least 1/2-inch above the waterline.

Check the Fill Valve for a Leak

At first, flush the toilet and look for a fill valve leak. Then lift on the toilet float arm when the tank is filling to see if the water stops. Then you adjust the toilet float arm, so the tank stops filling when the water level is 1/2- to 1-in. Below the top of the overflow pipe. If it’s still leak, then replaces it.

Remove and Replace the Old Toilet Fill Valve

At first, you turn off the water supply, flush the toilet, and sponge the remaining water from the tank. Then you disconnect the water supply line, unscrew the fill valve locknut and lift out the old fill valve.

Install the new fill valve and tighten the locknut.

If the fill valve is at its maximum height, the overflow pipe is still higher than the critical level mark, shorten the overflow pipe with a hacksaw, so it's 1 inch. Lower than the significant level mark on the fill valve.

Connect the Fill Tube

At first, you can connect a new fill tube to the fill valve nipple and the other to the enclosed angle adapter. Then you clip the angle adapter into the overflow pipes.

Finish the installation process by connecting the flapper chain to the flush lever. At last, you turn on the water and test flush the toilet.

How to fix a running toilet without a ball float

Various reasons can cause the water to keep leaking without stop. The toilet tank is stopping from the self-pumping pool or more complex. Here are some common reasons and how to fix a running toilet without a ball float.

1 Check the water level

A water level can cause the toilet to leak. The high water levels will overflow through the spillway. The spillway is located in the middle of the tank that connects the water tank to the toilet.

If the water flows continuously into the spillway, adjust it by lowering the float. This fault is caused by the supply of water that is draining. It also creates a clogged pipe leading to the toilet.

2 Determine which float type you are using

The float is connected to the water supply pipe to adjust the water level low or high. There are two main types of ball float, such as Round float, Balloon float. Round float, the toilet drain will have a horizontal bar with one end connected to the water supply valve. Balloon float, as the name implies, has a small cylinder that surrounds the water supply valve.

3 Due to broken buckle

The gardener toilet must remove the entire valve assembly and the buoy. Clean and reinstall if you can't use it. It's just a dirty hotel, replace toilet seat lock. But if you can't do that, you should replace the valve lock or replace the bucket valve buoy.

Conclusion

A toilet includes many parts that have to work together for the bathroom to function correctly. A toilet can easily make nickel and dime you if you aren't careful.

Replacing the whole shower is often the most cost-efficient solution. So you can repair only the parts that are damaged and need to improve them. A toilet repair kit can help you to overcome these problems.